图片
免费，登录即可下载
发布时间：2021/1/22 17:29:00
用于促进Flyingbaar P905机械的模型，在p905H模型测试，轴承可以使用固定的，安装在自己的手推车或印刷的PLA塑料。对于X轴架，增加了一个悬挂式前列腺，用于安装BLTouch传感器，并在4020库仑下加固。该产品目前正在开发和测试中，很快将在这里发布。
Update 13.02.2019
添加了一个新的正确固定的BLTouch传感器，以方便维修挤出机，它变得更加严格，增加了一个孔来调整喷嘴，加热器更好地插入在前面的块，否则很难改变。增加了霍尔德来支撑散热在两个版本的你的口味，增加了散热版本的2个喷嘴同时，模型的时间，将进一步完善，设计结束后，将立即添加散热版本单独在喷嘴。
更新26.03.2019
增加了两个喷嘴用涡轮机。原始链接吹风
Models to facilitate the mechanics of Flyingbaar P905，tested on the model P905H，bearings can be used regular，which are italled on native carriages，or printed from PLA plastic.在X-axis carriage，a higed spacer has been added to itall the BLTouch seor，and the mount for the 4020 airflow is currently under development and testing，and I will also post here soon.
Update 02 13 2019
Added a new correct mounting for the BlTouch seor to make it convenient to maintain the extruder，it became more rigid，holdes for adjusting the nozzles were added，it is better to iert the heat into the blocks in the front，otherwise it is hard to change.A holder for attaching airflow in two veio to your taste is added，a veion of airflow for 2 nozzles at the same time is added，the model is temporary，it will be further developed，after the design is completed，the airflow veio will be immediately added to the nozzles separately.
Update 26.03.2019
额外的blowing on 2 nozzles using impelle。原空气流在线 as the airflow is designed for a 30°30°10 cooler，then I made an adapter for the 4020 impeller for it.：再过一次，我更新了holder for the BLTouch。VERY IMPORTANT解码！The impeller with a zero coordinate on X is beyond the size of the printer，so if you use auto calibration with BLTouch，you need to reduce the measurement area so that the carriage does not rest on the Y axis motor.
Update 13.02.2019
添加了一个新的正确固定的BLTouch传感器，以方便维修挤出机，它变得更加严格，增加了一个孔来调整喷嘴，加热器更好地插入在前面的块，否则很难改变。增加了霍尔德来支撑散热在两个版本的你的口味，增加了散热版本的2个喷嘴同时，模型的时间，将进一步完善，设计结束后，将立即添加散热版本单独在喷嘴。
更新26.03.2019
增加了两个喷嘴用涡轮机。原始链接吹风
Models to facilitate the mechanics of Flyingbaar P905，tested on the model P905H，bearings can be used regular，which are italled on native carriages，or printed from PLA plastic.在X-axis carriage，a higed spacer has been added to itall the BLTouch seor，and the mount for the 4020 airflow is currently under development and testing，and I will also post here soon.
Update 02 13 2019
Added a new correct mounting for the BlTouch seor to make it convenient to maintain the extruder，it became more rigid，holdes for adjusting the nozzles were added，it is better to iert the heat into the blocks in the front，otherwise it is hard to change.A holder for attaching airflow in two veio to your taste is added，a veion of airflow for 2 nozzles at the same time is added，the model is temporary，it will be further developed，after the design is completed，the airflow veio will be immediately added to the nozzles separately.
Update 26.03.2019
额外的blowing on 2 nozzles using impelle。原空气流在线 as the airflow is designed for a 30°30°10 cooler，then I made an adapter for the 4020 impeller for it.：再过一次，我更新了holder for the BLTouch。VERY IMPORTANT解码！The impeller with a zero coordinate on X is beyond the size of the printer，so if you use auto calibration with BLTouch，you need to reduce the measurement area so that the carriage does not rest on the Y axis motor.
|
共0个文件
压缩包大小：3MB
|
||
|---|---|---|
微信小程序
微信扫码打开此模型
迪威模型
微信扫码支付