OpenVent-3D可打印BVM通风机，A2设计，BLDC电机安装

During the Corona (COVID-19) pandemic it became obvious that a lack of medical equipment can cause a severe impact. Often, also simple equipment and desig can be helpful as long as no professional equipment is available.
This repository contai generic information about an open-source ventilator device. Main purpose of this project is to build a ventilator when no professional and medical equipment is available. Easy to assemble and available components are used with a clear focus on simplicity, availability and scalability.
This project started as part of the #WirvsVirus Hackathon of the German government and is inteively being worked on since, including exchange with medical experts. The work is also a selected project in the give-a-breath-challenge and The Global Hack.
Please check the full disclaimer as well before proceeding:
The material and documentation here is provided with no warranties explicit or implied.
No material on this site is intended to provide medical advice. All desig are intended for investigational use only.
This site does not represent any official policies or procedures.
The project is provided "as is", without warranty of any kind, express or implied, including but not limited to the warranties of merchantability, fitness for a particular purpose and noninfringement.
In no event shall the autho or copyright holde be liable for any claim, damages or other liability, whether in an action of contract, tort or otherwise, arising from, out of or in connection with the software or the use or other dealings in the software.
Only use this repository, desig, documentation or any provided information if you accept the above disclaimer.
Additional discussion, documentation, source code, electronics and seor design is available atGitHub( and YouTube( and DevPost(
This thing represents a further exteion / variant based on our evolved design A1. Further exteio and upgrades will be posted here as well. Please check those, too.
General concept
An AMBU-bag is used as pressure reservoir. It already features an O2 inlet (O2 concentration is crucial for patients with acute respiratory syndrome) and several safety features including e.g. overpressure and bypass valves. Being standard for emergency help, these bags are available at substantial volumes.
A motorized and microcontroller seor controlled setup squeezes the bag at the right pattern, supporting assist-, pressure-, volume- and flow-control ventilation and exhaled gas measurements and filte. Our Implementation is based on hardware compatible to Arduino, an #Infineon XMC4700 Relax Kit and a Stepper Motor Control Shield with IFX9201 and XMC1300 on it. Among other seo, two pressure seo DPS368 are used for differential pressure detection. The user interface includes a commonly available I2C LCD Display Module 128 x 64 Pixel for Arduino.
All is based on open source and commonly accessible parts; especially for the mechanics the objective is to be scaleable in production and hence fully 3D-printable. Only the motor and it's screws as well the belt is not printed. Standard stepper moto such as Nema-23 are proposed. Electronics, seo and software are covered in our GitHub pages.
Improvements
Based on the positive experience and confirmation of robustness with the already evolved A1 design, we aimed at improving the actual usability even further, specifically removing or hiding the belts/ropes across the ambu bag as they could potentially become a source of error in practical daily use. At the same time, the objective was, to not increase the required build volume and also to keep print time/volume within bounds. The presented design cove both and a really solid frame to hold the bag and keep it from moving around as an additional benefit. The optimal height of the punch block is yet to be confirmed. The actual design can easily be scaled vertically to experiment with different sizes.
Experiences
This design has proven to be extremely robust, whilst still simple in design. The increase in print-complexity vs. the initial A0 design is moderate and slightly reduced vs. the A1 design. On standard printe with little less than 20cmx20cm build area this would typically require two sequential print jobs. Still it can be done in less than 18 hou at 0.25mm layer resolution (350g). Robustness has higher priority than printing time. However, such high resolution is not required for the design, hence additional speed-up potential is given.
While this design enable 'smaller' motor variants such as a Nema-17, these can become very warm under (rather theoretical) continuous maximum load, and thus the rotor should be printed from high temperature PLA/material. Nema-23 appea to be the preferred choice. More detailed discussio on our GitHub pages.