修改

图片

迪威模型和Solidworks 联合会员

Z轴稳定杆

免费,登录即可下载
发布时间:2020/6/15 8:17:00
这一Z轴稳定器棒模型具有相当大的坚固性,上部支架与3个螺丝连接到Z-X轴线和螺丝轴承轴承轴承,下部连接到主剖面,同时按住上部壳体和下部壳体,每个栏杆都有螺丝,可以精确调整。
这个模型还有电源电缆和磁带的保护罩和盖子这样我们就可以得到所有的保护了
你可以顺利地滑动下盖子
模型上有可调整的孔,可以在20个Artillery X1中有效,因为测试结果因20个不同而各异,所以要做一个标准模型来解决这个问题。
我根据20台X1打印机的情况做了一些修改,因为最终职业探测器的位置、螺丝等等都有变化。
包括3个型号的10mm 14mm条,推荐的1mm铁或钢条
我输入了一些模型,根据用户的要求削减了中队,因为有了控制轴Z的面料,标准模型与他们发生了冲突。
聚氯乙烯
如果有人想加入的话,我可以加入
建议的印刷要有一定的刚性和耐久性,因为它必须与我所希望的稳定性,我的配置和我推荐的是层高0.2个口0.4,4个更高的墙周长 4 4,和35%的小型填充在PETT。
这是一个昂贵的时间和材料,因为它将是大约500克,但你只需要打印一次,所以我建议它是牢固的。
螺栓可能因地区和需要的不同而有差异,但我会说明使用的螺栓和最小的措施,许多原来的螺栓可以使用,但由于质量差,我建议视需要重新安装。
我需要的螺丝是:
2×M320mm(电子盖子的底部)
2×M416mm(外部高级囚犯)
4×M48mm(高级内部和下内部囚犯)
2×M410mm(外围条状囚犯)
8×M520mm(低于总表)
4×M512mm(以Z轴中队为单位)
2×M5转为t(以Z轴为单位)
2×M550mm(Z轴对X轴外部上)
4×M58mm(Z轴承)
4×M510mm(轴向至底盘轴承支撑)
2×10/12/14MM59.7cm(钢筋/铁)
测试结果在β测试中相当显著,因为其他类型的约束总是会发生变化。
我希望你们能像在意大利的案子中一样利用他
请记住,您可能需要一些改变或修改,我很乐意听到您的植入。
目前正在进行的第35级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级目前正在进行的第35级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级这是一个多月以前评论
This model of stabilizer BA for the Z axis has a fairly strong strengness,the Upper supports connect with 3 screws to the Z and X axis and to the spindle bearing,on the lower axis it connects to the main profiles while holding the upper housing and holding the bottom case,the BA are fastened with screws for their exact fit.
The Model also has protecto and cover for cables and current tapes,so we have everything protected at 11.
The bottom cover could be removed by sliding without problems.
The models have adjustable holes to be valid in any veion of artillery x1 since in the tests you carry out them varied according to the veion having to make an standard model to correct this problem
i include several modificatio depending on the artilley x1 printer veion because the position of the limit switches,screws,.
i include 3 models for types of BA 10mm 12mm 14mm,recommended 1mm BA iron or steel
i include models with the square cut out at the request of use,since having the control3d Z-Axis cariages italled,the standard model collides with them.
聚氯乙烯 has a channel on youBue, through his channel since it is one of the most experts in this country)
i include a TPU gasket model in case they want to add it to the supports.
Printing with enough regidity and resistant material is recommended,since it has to achieve the desired stability,my configuration and it is what I recommend was layer height 0.2 nozzle 0.4,4 wall perivie 4 upper 4 lower and 35%minimum fill in petg
It is expective set in time and material since they will be approximately 500g but you will only have to print once so I recommend making it strong and firm
The Screws can change in distance according to the area and the need,but I will indicate the ones used and the minimum measures,many of the original screws can be used,but due to their poor quality,I recommend putting new ones as needed.
The screws that I needed were the following:
2×M3 20mm(Bottom Bracket for Electronic Cover)
2×M4 16mm(Upper Outer Stud BA)
4×M4 8mm(Inner top studd and bottom inner studds)
2×M4 10mm(outer lower studd ba)
8×M5 20mm(Lower fastening to the general picture)
4×M5 12mm(Bracket Z Axis Bracket)
2 X M5 T-NUT(Bracket for Z Axis Bracket)
2×M5 50mm(Fastening Z Axis to Upper X Axis outside)
4×M5 8mm(呼喊Z Spindle Bearing)
4×M5 10mm(Fastening bearing z axis bearing to chasis)
2×10/12/14mm 59.7cm maximum(steel/iron ba)
The tests carried out are quite remarkable in the beta-test since with other types of fastening they always had oscillation
I hope they can get the same utility as in the already italled cases
Remember that it may need some variation or modification and I would be delighted to hear it to implement it.
0个文件
压缩包大小:25MB
小程序二维码
微信小程序 微信扫码打开此模型
登录后发表评论
恒诺鑫科-专注碳素制品的开发与生产