图片
免费，登录即可下载
发布时间：2021/1/30 7:36:00
2019-03-11: pytherion is making a marvelous addition, a wrecker set -up for this type of truck:
It should be possible to mod it to the scale of my truck when its done.
2019-03-10: I printed the parts and found the axle housings are not correct. So I removed those files and I will reload them when done. Sorry! Next time I'll upload after making them
2019-03-09: I added a lot of rear axle and suspeion parts for those axles. The axles are a remix of Mr. Crankyface's rear axle and diff. Actually I just widened his axle to 140 mm and made a double veion which can drive the second of the rear axles. I will also lengthen and change the drive shafts from diff to wheel and added a wheel hub to them. The required bearings 6700ZZ. The diff pin is 18x4 mm metal, I cut two pieces from a 4mm nail. I print almost everything at 0,2 mm, but the finer suspeion parts and the gea I chose to print at 0,1 mm layer height. I printed the four drive shafts on a raft.
2019-02-16: I've updated the grille. I found a Peterbilt model on GrabCAD and although I cannot mod it in the software I use, I made dxf views of it to base my model on. On the pictures you still see the prototype, the STL has slightly better mountings of the lights. On the pictures it's a bit too flimsy. This design also lets a lot of air in, so the electronics that will be mounted under the hood will have some ventilation.
2019-02-10:This is the fit part of a long process, I am aiming to make an RC Truck 1:10 scale, with a trailer onto which I can put my 1:10 scale touring ca. I have no idea where and when this will come to an end. But the process itself is very nice.
This grille is the fit part and I already printed it. Not because I think it is final, but because it will serve as an ipiration sitting on my desk.
Please feel free to comment positively. Please bear in mind this will not be a scale model, I just look at photos of the Peterbilt 359 and make what I like.
I would like to express my gratitude to Mr. Crankyface for posting all his work on his RC trucks. His work is a great ipiration and I am sure I will use some drive train parts he designed in this project, either modified or unmodified.
It should be possible to mod it to the scale of my truck when its done.
2019-03-10: I printed the parts and found the axle housings are not correct. So I removed those files and I will reload them when done. Sorry! Next time I'll upload after making them
2019-03-09: I added a lot of rear axle and suspeion parts for those axles. The axles are a remix of Mr. Crankyface's rear axle and diff. Actually I just widened his axle to 140 mm and made a double veion which can drive the second of the rear axles. I will also lengthen and change the drive shafts from diff to wheel and added a wheel hub to them. The required bearings 6700ZZ. The diff pin is 18x4 mm metal, I cut two pieces from a 4mm nail. I print almost everything at 0,2 mm, but the finer suspeion parts and the gea I chose to print at 0,1 mm layer height. I printed the four drive shafts on a raft.
2019-02-16: I've updated the grille. I found a Peterbilt model on GrabCAD and although I cannot mod it in the software I use, I made dxf views of it to base my model on. On the pictures you still see the prototype, the STL has slightly better mountings of the lights. On the pictures it's a bit too flimsy. This design also lets a lot of air in, so the electronics that will be mounted under the hood will have some ventilation.
2019-02-10:This is the fit part of a long process, I am aiming to make an RC Truck 1:10 scale, with a trailer onto which I can put my 1:10 scale touring ca. I have no idea where and when this will come to an end. But the process itself is very nice.
This grille is the fit part and I already printed it. Not because I think it is final, but because it will serve as an ipiration sitting on my desk.
Please feel free to comment positively. Please bear in mind this will not be a scale model, I just look at photos of the Peterbilt 359 and make what I like.
I would like to express my gratitude to Mr. Crankyface for posting all his work on his RC trucks. His work is a great ipiration and I am sure I will use some drive train parts he designed in this project, either modified or unmodified.
|
共0个文件
压缩包大小：2MB
|
||
|---|---|---|
微信小程序
微信扫码打开此模型
迪威模型
微信扫码支付