板适配器（mksskr+Mosfet）

Under development and continuous improvement.
ANET ET4 adapter to Itall SKR or MKS Board IIDE the al，you can use also“Mosfet Holder”to Itall Two Small Boards.
Files:*Mosfet adapter:works properly，but the design will be revised to make some improvements.
*Board Adaper MKS：Works Properly。USB and microd holes matches perfectly.
*Board Adaper SKR：Design adapted by@ibility with SKR 1.4 probed by him（I strongly recommend look his thingivee profile，especially“igneus”creation）.Its necessary to sand a little bit the holes of USB and microd card.
Assembly Itrucito
仅使用两种原始的文字来描述调整后的结构（那些并非董事会之后的文字）。You need to add also two washe.这也是建议使用两个楼顶。为了让董事会能够适应，你需要三个小Screws。
目前正在进行的第35级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级目前正在进行的第35级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级（b）根据《公约》第22条第（1）款和第35条第（2）款，/第35条，/第35条，/第35条，/第35条，/第35条，/第35条，/第35条，/第35条，/第35条，/第35条，/第35条，/第25条，/第35条，/第35条，%
目前正在进行的第35级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级目前正在进行的第35级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级级（b）根据《公约》第22条第（1）款和第35条第（2）款，/第35条，/第35条，/第35条，/第35条，/第35条，/第35条，/第35条，/第35条，/第35条，/第35条，/第35条，/第25条，/第35条，/第35条，%
持续发展和改善
用原锚将SKR或MKS板固定在ANET ET4内的适配器此外，可使用“Mosfets支架”来为两个外来的Mosfets注入意大利。
档案：*Mosfet Adapter：两个Mosfet板的功能支持。今后将对其进行审查，并作一些改进。
*Board Adaper MKS：实用设计。USB端口和显微镜与外壳上的洞相吻合，不需要磨砂，除非SD卡很公平。
*Board Adapter SKR：Design adapted by@matosos.由他自己验证SKR 1.4警徽的兼容性（强烈推荐访问您的Thingivee配置，特别是[Igneus].卡通设计）
剪辑片断
用两个原螺丝钉将底盘接受器（不在接受器下的螺丝）插上。需要增加两个垫子，我还建议用双面带来加强固定，板上有三个小螺丝的适配器。