发布时间：2024/1/19 0:11:00
Dragonfly is a 3D printed 2" micro quad designed to be made out of PETG, Nylon12 or Polycarbonate, which are reasonable strong materials. And it is designed to fly like a 5" quad... Providing a great platform for indoor flying, or simply to learn to fly quads LOS or FPV. Its especial good for back garden flying, crucially it is below the 250 gm weight limit for CAA or FAA registration.
The quad weighs about 104 gm and the motor can produce up to 250 gm of thrust depending on the battery pack used, providing an exciting but predictable flight experience.
Here is a link to a video of actual flight footage . To follow..
Parts List
Micro Quad - Parts List for 2.5” Kwad
updates adding; props, batteries, antenna tubes & screws…
So, you have three cost optio☺
Parts full PFV Quad £480 everything you need – including RC Tramitter & Goggles
Ready To Fly £200 - incl batteries, charger, & TX.
Bind aNd Fly £90 Just add radio, batteries, goggles, & charger
I would recommend you went with option 1, the RC Tramitter & Goggles will work with our larger drone too☺
If you could use the affiliate links when ordering from Banggood - I gain affiliate points for that and small kickback each order - you pay the same price… When ordering filament, please use this referral link to register with before ordering . This helps refund all my research projects with 3D printing and drone desig…
FatShark Attitude V4 goggles - £255 - DVR included
This is a great pair of goggles
Fatshark Dominator HD3 - Top of the range goggle -
Tramitter - QX7 - Remember Mode 2 left hand throttle.. £79.19
Green, Orange, Blue, White & Black
VTX - £9.34
RX - FKY - XSR - £13.23
2” Tri-blade Props - £2.34
2.5” Tri-blade Props
Gemfan Flash 2540-3 Propelle 2.5x4.0 Inch Triblade Props 3-Blade Compatible with 1104 -1105 FPV Mini Racing Moto (Pack of 12 Pai,Mix Colo)
Gemfan Flash 2540 2.5x4 2.5 Inch 3-Blade Propeller with 1.5mm Mounting Hole – 4 pai - £2.70
4 in 1 - 12A or 25A ESC - £23.45 or £27.36
STM32F4 - Beta Flight Flight Controller OMNI F4 - with BEC & OSD - £13.29
BR1106 3800KV Brushless Moto - £25.41
FPV Camera - RunCam Micro Swift 600TVL 2.1mm/2.3mm £23.45
Miniature GoPro - £9.38
Batteries - 2S; 25g & $8.99, 3S 37g $10.99 & 4S 48g $12.99
2S low price, low power great for flying with a bear frame, nothing else a good beginne option…
3S Great for flying a VTX & FPV camera and additional TPU radio tray and camera mount
4S Great for flying with, additional TPU parts, FPV camera & VTX & a miniature GoPro
Amazon
2S, 350 mAh, 26 gms, Makerfire - £9.99
2S, 600 mAh, 32 gms, GNB - £9.99
Newbeedrone {US custom charge but great batteries}
2S -
3S -
4S -
Quadcopter uk - a little heavy - £10.
3S -
4S -
Black M3 Nylon hex standoff, screw & nut kit - £5.92
or on Amazon
Antenna Tubes - £1.90
XT-30 leads - £6.99
Battery Straps - £5.99
Battery Charger £16.95 or £46.91
The cheaper is good enough to start with but £46 pound is very nice…
Battery bags 3 for £3.06
Filament for the Frame - you pas your money and takes your choice, I would go with PETG, White Nylon or Black Carbonite, for the flexible material TPU or flexible PLA work equally well… If you go for a fun pack I could print an number of alternate parts. produce high quality filaments, its not work buying from another source unless it Verbatim on Amazon.
Please use this referral link to register with
PETG – Highly recommended - £28.96 produces a very strong durable Kwad
Nylon 12 - Qty 10m, 1.75mm, £7.45 - easy to print - produce an exceptionally strong durable light Kwad
White only -
Carbonite - Qty 10m, 1.75mm, £10.96, difficult to print. (This is our best option for a light, durable racing quad)
Black -
ABS - Qty 10m, 1.75mm, Strong & durable, but difficult to print. 5 x 10m, 1.75mm, £13.96
Fun Pack -
PLA - Many Colou beautiful Print Quality not as durable as Nylon, Carbonite or ABS… 5 x 10m, 1.75mm, £13.96
Fun Pack -
PLA A vibration absorbing and less brittle veion of PLA, very durable. 7 x 5m, 1.75mm, £27.95
Battery and Camera mount TPU or Flexible PLA
Thermoplastic PolyUrethane - 1.75mm, 7 x 5m, £42.95. or 10m x 1.75mm £6.46
Fun Pack -
individual -
Flexible - PLA 1.75 with 6 x 10mm for £26.95 or £4.96 each
Fun Pack -
individual -
Alternative Frame - Carbon - £30.49
Prop screws M2 x 7mm button head. Screws
Motor bolts - M2.5 x 8mm capped head x 16
Arm screws - M1.2 x 4mm counteunk cross head self tapping screw… x 4 mm cross head counteunk self tappe
RGB LEDs - WS2812 24 bit true colour LED -
Firmware setting a lot more to come here…
Chrome App’s
Betaflight -
BL_Heli_S -
OpenTX - for TX & RX -
Custom mix settings
resource MOTOR 1 B00
resource MOTOR 2 B01
resource MOTOR 3 A03
resource MOTOR 4 A02
Moto
1 = 1
2 = 4
3 = 3
4 = 2
so CLI commands
resource MOTOR 2 A02
resource MOTOR 4 B01
save
resource MOTOR 1 B00
resource MOTOR 2 A02
resource MOTOR 3 A03
resource MOTOR 4 B01
Learning to fly a :
The quad weighs about 104 gm and the motor can produce up to 250 gm of thrust depending on the battery pack used, providing an exciting but predictable flight experience.
Here is a link to a video of actual flight footage . To follow..
Parts List
Micro Quad - Parts List for 2.5” Kwad
updates adding; props, batteries, antenna tubes & screws…
So, you have three cost optio☺
Parts full PFV Quad £480 everything you need – including RC Tramitter & Goggles
Ready To Fly £200 - incl batteries, charger, & TX.
Bind aNd Fly £90 Just add radio, batteries, goggles, & charger
I would recommend you went with option 1, the RC Tramitter & Goggles will work with our larger drone too☺
If you could use the affiliate links when ordering from Banggood - I gain affiliate points for that and small kickback each order - you pay the same price… When ordering filament, please use this referral link to register with before ordering . This helps refund all my research projects with 3D printing and drone desig…
FatShark Attitude V4 goggles - £255 - DVR included
This is a great pair of goggles
Fatshark Dominator HD3 - Top of the range goggle -
Tramitter - QX7 - Remember Mode 2 left hand throttle.. £79.19
Green, Orange, Blue, White & Black
VTX - £9.34
RX - FKY - XSR - £13.23
2” Tri-blade Props - £2.34
2.5” Tri-blade Props
Gemfan Flash 2540-3 Propelle 2.5x4.0 Inch Triblade Props 3-Blade Compatible with 1104 -1105 FPV Mini Racing Moto (Pack of 12 Pai,Mix Colo)
Gemfan Flash 2540 2.5x4 2.5 Inch 3-Blade Propeller with 1.5mm Mounting Hole – 4 pai - £2.70
4 in 1 - 12A or 25A ESC - £23.45 or £27.36
STM32F4 - Beta Flight Flight Controller OMNI F4 - with BEC & OSD - £13.29
BR1106 3800KV Brushless Moto - £25.41
FPV Camera - RunCam Micro Swift 600TVL 2.1mm/2.3mm £23.45
Miniature GoPro - £9.38
Batteries - 2S; 25g & $8.99, 3S 37g $10.99 & 4S 48g $12.99
2S low price, low power great for flying with a bear frame, nothing else a good beginne option…
3S Great for flying a VTX & FPV camera and additional TPU radio tray and camera mount
4S Great for flying with, additional TPU parts, FPV camera & VTX & a miniature GoPro
Amazon
2S, 350 mAh, 26 gms, Makerfire - £9.99
2S, 600 mAh, 32 gms, GNB - £9.99
Newbeedrone {US custom charge but great batteries}
2S -
3S -
4S -
Quadcopter uk - a little heavy - £10.
3S -
4S -
Black M3 Nylon hex standoff, screw & nut kit - £5.92
or on Amazon
Antenna Tubes - £1.90
XT-30 leads - £6.99
Battery Straps - £5.99
Battery Charger £16.95 or £46.91
The cheaper is good enough to start with but £46 pound is very nice…
Battery bags 3 for £3.06
Filament for the Frame - you pas your money and takes your choice, I would go with PETG, White Nylon or Black Carbonite, for the flexible material TPU or flexible PLA work equally well… If you go for a fun pack I could print an number of alternate parts. produce high quality filaments, its not work buying from another source unless it Verbatim on Amazon.
Please use this referral link to register with
PETG – Highly recommended - £28.96 produces a very strong durable Kwad
Nylon 12 - Qty 10m, 1.75mm, £7.45 - easy to print - produce an exceptionally strong durable light Kwad
White only -
Carbonite - Qty 10m, 1.75mm, £10.96, difficult to print. (This is our best option for a light, durable racing quad)
Black -
ABS - Qty 10m, 1.75mm, Strong & durable, but difficult to print. 5 x 10m, 1.75mm, £13.96
Fun Pack -
PLA - Many Colou beautiful Print Quality not as durable as Nylon, Carbonite or ABS… 5 x 10m, 1.75mm, £13.96
Fun Pack -
PLA A vibration absorbing and less brittle veion of PLA, very durable. 7 x 5m, 1.75mm, £27.95
Battery and Camera mount TPU or Flexible PLA
Thermoplastic PolyUrethane - 1.75mm, 7 x 5m, £42.95. or 10m x 1.75mm £6.46
Fun Pack -
individual -
Flexible - PLA 1.75 with 6 x 10mm for £26.95 or £4.96 each
Fun Pack -
individual -
Alternative Frame - Carbon - £30.49
Prop screws M2 x 7mm button head. Screws
Motor bolts - M2.5 x 8mm capped head x 16
Arm screws - M1.2 x 4mm counteunk cross head self tapping screw… x 4 mm cross head counteunk self tappe
RGB LEDs - WS2812 24 bit true colour LED -
Firmware setting a lot more to come here…
Chrome App’s
Betaflight -
BL_Heli_S -
OpenTX - for TX & RX -
Custom mix settings
resource MOTOR 1 B00
resource MOTOR 2 B01
resource MOTOR 3 A03
resource MOTOR 4 A02
Moto
1 = 1
2 = 4
3 = 3
4 = 2
so CLI commands
resource MOTOR 2 A02
resource MOTOR 4 B01
save
resource MOTOR 1 B00
resource MOTOR 2 A02
resource MOTOR 3 A03
resource MOTOR 4 B01
Learning to fly a :
|
共个文件
压缩包大小：7MB
|
||
|---|---|---|
微信小程序
微信扫码打开此模型
迪威模型
微信扫码支付