发布时间：2024/1/7 3:22:00
Video can be found here:
Editable Fusion 360 source files can be found here:
This linear actuator is almost completely 3D printed (except for the thread and some bolts, nuts and bearings).I curently don't have any position feedback or limited switches italled on it, I will add them in the feature when I'm going to integrate it in a projecct. It has a speed of about 25 mm on a 9V battery and draws about 1.7 Amps of curent. The motor is rated for 36 Volts. Running the linear actuator on a 36 Volt battery will increase the speed of the actuator. The tramission is a belt driven one wich uses a GT2 timing belt and a 3D printed GT2 pulley, This may not be the most ideal tramission for this task but it'll do for some testing. The linear actuator uses an M8 thread to convert the rotating motion into a linear motion. All parts (except for the 120 teeth pulley) are printed with a 1 mm nozle because there is no high accuracy required and it goes a lot faster. Some people are sceptic about using a 1mm nozzle but I think it's good for printing large objects like these without the need for accuracy. And it works great for me.
Video can be found here:
More info can be found here:
Components used:
1 × l298N motor driver
link:
1 × Arduino nano V3
link:
1 × 775 electric motor 36 Volt
link:
1 × Pulley for motor side, 5mm bore, 16 teeth
link:
2 × 8mm inner diameter bearings
link:
1 × Gt2 timing belt 260-GT2-6
1 × M8 thread rod
7 × M8 nuts
Recommended tools:
3D-printer:
All my project files, itructio, schematics, are provided for free so everyone around the world can enjoy them. Feel free to support me so I can create and share even more awsome projects. Any amount of support is greatly appreciated :-)
Feel free to take a look at my other desig:
3D printable antweight battlebot: Bulldog:
SpaceX ipired edf rocket:
3D printed high torque servo/gearbox veion 2:
UMC - Univeal motion controller:
3D-printable Davinci catapult gift card:
Arduino controlled photogrammetry 3D-scanner:
Fully 3D-printable turntable:
RC FPV tank rover:
Fully 3D-printable wind-up car gift card:
3D-printable High torque servo/gear reduction:
'BOOM box' high voltage capacitor bank case:
Subby the interactive youtube subscriber robot:
robot hand || bionic hand prosthesis prototype:
3D-printable linear actuator:
Mini 3D-printable crossbow:
8 legged spider robot:
best 3D-printable bearing:
Have a nice day!
Editable Fusion 360 source files can be found here:
This linear actuator is almost completely 3D printed (except for the thread and some bolts, nuts and bearings).I curently don't have any position feedback or limited switches italled on it, I will add them in the feature when I'm going to integrate it in a projecct. It has a speed of about 25 mm on a 9V battery and draws about 1.7 Amps of curent. The motor is rated for 36 Volts. Running the linear actuator on a 36 Volt battery will increase the speed of the actuator. The tramission is a belt driven one wich uses a GT2 timing belt and a 3D printed GT2 pulley, This may not be the most ideal tramission for this task but it'll do for some testing. The linear actuator uses an M8 thread to convert the rotating motion into a linear motion. All parts (except for the 120 teeth pulley) are printed with a 1 mm nozle because there is no high accuracy required and it goes a lot faster. Some people are sceptic about using a 1mm nozzle but I think it's good for printing large objects like these without the need for accuracy. And it works great for me.
Video can be found here:
More info can be found here:
Components used:
1 × l298N motor driver
link:
1 × Arduino nano V3
link:
1 × 775 electric motor 36 Volt
link:
1 × Pulley for motor side, 5mm bore, 16 teeth
link:
2 × 8mm inner diameter bearings
link:
1 × Gt2 timing belt 260-GT2-6
1 × M8 thread rod
7 × M8 nuts
Recommended tools:
3D-printer:
All my project files, itructio, schematics, are provided for free so everyone around the world can enjoy them. Feel free to support me so I can create and share even more awsome projects. Any amount of support is greatly appreciated :-)
Feel free to take a look at my other desig:
3D printable antweight battlebot: Bulldog:
SpaceX ipired edf rocket:
3D printed high torque servo/gearbox veion 2:
UMC - Univeal motion controller:
3D-printable Davinci catapult gift card:
Arduino controlled photogrammetry 3D-scanner:
Fully 3D-printable turntable:
RC FPV tank rover:
Fully 3D-printable wind-up car gift card:
3D-printable High torque servo/gear reduction:
'BOOM box' high voltage capacitor bank case:
Subby the interactive youtube subscriber robot:
robot hand || bionic hand prosthesis prototype:
3D-printable linear actuator:
Mini 3D-printable crossbow:
8 legged spider robot:
best 3D-printable bearing:
Have a nice day!
|
共个文件
压缩包大小：4MB
|
||
|---|---|---|
微信小程序
微信扫码打开此模型
迪威模型
微信扫码支付